The Following Things About LED Grow Strip Lights That You Must Know!

October 29, 2018

What is LED Grow Strip Lights?

The strip refers to the LED lamp is welded to the copper wire or the strip flexible circuit board with the special processing technology, and then connected to the power source to emit light, because its luminous shape is like a strip of light. The earliest process is to weld LED to copper wire, then to cover PVC pipe or directly shape the equipment. There are two types: round and flat. The titles are divided according to the number of copper wire and the shape of the led lamp belt. Flat on the front plus flat word, that is, flat second line. Later, it developed into using the flexible circuit board or FPC as the carrier, which gradually replaced the earlier processing technology due to its simpler processing technology, easier quality control, longer life and higher color and brightness. And the Led Plant Light belt refers to the special plant light supplement.

Main Features and Advantages of the LED Grow Strip Lights

1.Soft and can curl like a wire.

2. Able to cut and extend.

3. The bulb and circuit are completely wrapped in flexible plastic, with good insulation and waterproof properties, and safe to use.

4. Strong weather resistance.

5. No rupture, long service life.

6. Easy to follow and use, it has been widely used in gardens, courtyards, and greenhouses.

The Span Life Of LED Grow Strip Lights

Since LEDs are constant-current components, LED plant light strips produced by different manufacturers to have different constant-current effects and, of course, different life spans. All of the products of Xinjia choose the best raw materials, and with ten years of technical experience, the service life of the Led Grow Lights are more than 50000 hours

What Should I Pay Attention to When Using the LED Grow Strip Lights?

1. Anti-static: as the LED is an electrostatic sensor, if the anti-static measures are not done during the maintenance of the LED lamp belt, the LED will be burned, resulting in waste.

2. Continuous high temperature: two important components of the LED lamp belt, LED and FPC, are products that cannot sustain high temperature. If the FPC is kept at a high temperature or exceeds its temperature, it will bubble the covering film of FPC and directly cause the LED lamp band to be scrapped. At the same time, the LED cannot endure the high temperature continuously, in the high temperature for a long time, its chip will be burned at high temperature. Therefore, the plant lamp belt should pay attention to heat dissipation after lighting for a period of time. At the same time, plants do not need up to 24 hours of irradiation.

How To Choose High-Quality LED Grow Strip Lights?

If we can identify the quality of LED strips from professional technology, I am afraid that many customers do not have this ability. But we can make a preliminary identification from the simple appearance, and basically distinguish the quality.

It can be identified from the following aspects:

1.Look at the solder joints. Regular LED strip manufacturer produces LED strip using SMT patch process, solder paste, and reflow soldering. Therefore, the welding spot on the LED lamp strip is relatively smooth and does not have much solder. The welding spot extends from the FPC welding pad to the LED electrode in an arc shape.

2. Look at the quality of FPC. FPC is divided into two types: copper and calendered copper. The copper foil on the copper plate is protruding, which can be seen from the joint between the pad and FPC. The calendered copper is closely connected with FPC and can be bent at will without the phenomenon of solder plate falling off. If the copper plates bend too much, the solder plate will fall off, and too high temperature during maintenance will cause the solder plate to fall off.

3. Check the cleanliness of LED lamp belt surface. The surface of the LED strip produced by SMT process is so clean that no impurities or stains can be seen. The fake LED strip, manufactured by hand welding process, will leave stains and traces of cleaning no matter how it is cleaned.

4.Look at the package. The regular LED strip will be packed with anti-static coil material, 5 meters or 10 meters roll, and sealed with anti-static and moisture-proof packaging bag outside the package. The LED strip of the low version is made of recycled coil material, and there is no electrostatic and moisture-proof packing bag. If you carefully look at the coil material, you can see the marks and scratches left when the label is removed.

5.Look at the labels. Regular LED strips will have printed labels on the packaging bag and reel, not printed labels.

6. See the attachment. Formal LED strips will be accompanied with instructions and specifications in the packaging box, and will also be equipped with LED strip connectors or clips. However, these accessories are not included in the packaging boxes of the fake LED lights, because some manufacturers can save money after all.

The Reason Why LED Grow Strip Lights Are Often Not On

1. The welding spot of the LED flexible light strip has the phenomenon of virtual welding, and the welding spot falls off due to the vibration during transportation, resulting in the lamp band is not on.

2. The soldering quality of the LED flexible lamp belt is poor, and the welding spot of the LED flexible lamp belt is prone to brittle and falling off in the bending process

3. When the LED flexible lamp belt is installed, the bending Angle is too large, which causes the LED flexible lamp belt welding spot to be separated from the copper foil, resulting in no light

4. Excessive extrusion of the product during the installation of the LED flexible lamp belt, resulting in the chip damage of the LED flexible lamp belt or the welding spot deformation falling off instead of lighting

5. The resistance welding layer of the circuit board of the LED flexible lamp is too thick, and the solder and circuit board cannot be completely integrated during welding, which is also a kind of virtual welding phenomenon.

6. The LED flexible light strip shall not be twisted during installation. If twisted, the welding spot of the LED flexible light strip will fall off, which will cause it not to light up.

7. The static electricity burns out because the LED is an electrostatic sensor. If there is no electrostatic protection, the chip will burn out.

The above is the The Following Things About LED Grow Strip Lights That You Must Know! we have listed for you. You can submit the following form to obtain more industry information we provide for you.

You can visit our website or contact us, and we will provide the latest consultation and solutions

Share to:

Send Inquiry

Previou:Why the LED Grow Lights Need to Aging Test?

Next:Why We Need LED Grow Lights?